What does the UNLOCKD Filling Spigot for 20 L Jug (60 mm) do?
The UNLOCKD Filling Spigot replaces the cap on a compatible 20 L jug, allowing you to dispense detailing liquids through a lever-operated tap. It gives you more control when refilling smaller bottles than pouring directly from a large jug opening, helping reduce splashes, overfilling and product waste. It is useful for professional detailing shops, mobile detailers preparing supplies and enthusiasts buying car-care products in bulk. The spigot controls liquid flow; it does not automatically measure quantities or dilute the product.
Will this 60 mm filling spigot fit any 20 L jug?
This spigot is intended for compatible 20 L jugs with a 60 mm threaded opening, but container capacity and opening diameter alone do not guarantee a correct fit. The thread profile and sealing surfaces must also match. Do not assume that another brand’s 20 L container, a five-gallon pail or a similarly sized jerry can uses the same closure. If you are unsure, confirm your container’s neck specification before ordering. A suitable connection should thread on smoothly by hand without forcing, cross-threading or leaving an uneven seal.
How do I install the spigot and refill a detailing spray bottle?
Start with the jug upright and the dispensing lever closed. Remove the original cap, inspect the threads and sealing surfaces, then screw the spigot onto the compatible opening by hand until secure. Carefully position and support the jug so liquid can reach the outlet without the container tipping or rolling. Place a clean, compatible bottle beneath the tap and open the lever gradually. Close it before the bottle reaches capacity, allow remaining drops to fall into the bottle, then cap and label your refill.
Can I use this jug tap with car wash soap, degreaser and other detailing chemicals?
Use the spigot only with liquids confirmed compatible with its materials and seals. Its chemical-resistant construction should not be interpreted as approval for every car wash concentrate, degreaser, acid-based cleaner or solvent. Compatibility depends on the actual formulation and concentration, not simply the product category. If suitability is unclear, confirm with UNLOCKD before dispensing that product. Thicker liquids may also dispense differently from thinner cleaners. Follow the chemical’s handling directions and use a receiving bottle suitable for storing the same formulation.
Does the filling spigot measure concentrate or create the correct dilution ratio?
No. The lever lets you control dispensing, but it does not provide a measured dose or mix concentrate with water. When preparing a diluted detailing product, measure the required amount using a suitable graduated container and follow that product’s dilution instructions and mixing sequence. Do not estimate concentration by counting seconds with the tap open, because liquid thickness, jug position and remaining volume can affect flow. Label the finished bottle with the product name and dilution so it is ready for consistent use.
Why is my 20 L jug spigot leaking or dripping?
Leakage can result from mismatched threads, a poorly seated seal, residue on the sealing surfaces or damage to the fitting. Close the lever and return the jug upright before inspecting the connection. Check that the threads are correctly aligned, the sealing area is clean and the fitting is secure without being overtightened. A few drops remaining in the outlet after dispensing differ from a continuous leak. If liquid continues escaping with the lever closed or around the connection, stop using the spigot until the cause is resolved.
How do I clean the filling spigot, and can I reuse it for another product?
Clean the spigot using a method compatible with both the previously dispensed liquid and the fitting. For water-rinsable products, follow the product manufacturer’s cleanup instructions and remove residue from the outlet, flow passage and sealing surfaces. Do not add an unfamiliar solvent or mix cleaning chemicals inside the tap. Dedicating one spigot to each product is a practical way to reduce cross-contamination. Before reuse, inspect for cracks, distortion, persistent residue or a lever that no longer closes properly, and replace damaged components rather than forcing them.
Can I leave the spigot attached when transporting a 20 L jug?
For transport, remove the dispensing spigot and reinstall the jug’s original closure securely. A dispensing lever can be bumped during loading or travel, and a leak-resistant tap should not be treated as a transport-rated cap. Keep the jug upright and secured against movement, following the liquid manufacturer’s storage and transport directions. For mobile detailers, filling smaller labelled bottles before departure also reduces the need to handle bulk containers at each appointment. Once back at your refill station, inspect and reinstall the spigot before use.
