What is included in the UNLOCKD Offroader Power Wash Pro Kit?
The kit pairs a Hypersuds Foam Cannon with your choice of 1 L or 4 L Offroader Power Wash Soap. The cannon spreads the soap over large exterior surfaces, while the formula is designed to loosen the mud, dirt, road film, and grime left by off-road driving. Choose 1 L for occasional trail washes or 4 L if you clean larger vehicles or wash more frequently. You will need a compatible pressure washer to operate the foam cannon; a pressure washer is not listed as part of the kit.
Which vehicles can I wash with the Offroader Power Wash Pro Kit?
The kit is intended for trucks, 4x4s, Jeeps, ATVs, UTVs, and other off-road vehicles that collect substantial exterior dirt. Its combination of heavy-duty soap and foam coverage is useful after trail rides, camping trips, muddy job sites, or drives on unpaved roads. The foam cannon helps distribute the wash solution across broad panels and exterior areas that are awkward to cover by hand. Check the vehicle maker’s cleaning guidance before washing exposed electrical components, sensitive finishes, or accessories.
Should I rinse thick mud off before applying the foam?
Yes. Rinse away loose debris and heavy clumps of mud before applying Offroader Power Wash. This keeps large particles from being dragged across painted surfaces later and gives the foam better access to the grime underneath. Once the vehicle is pre-rinsed, cover it evenly with the foam cannon, let the soap work without allowing it to dry, and rinse thoroughly. Inspect the surface before using a wash mitt: remaining dirt may need a careful contact wash, especially in seams, behind flares, and along lower panels.
How much Offroader Power Wash Soap should I put in the foam cannon?
UNLOCKD’s directions for Offroader Power Wash say to fill the foam cannon bottle with warm water and add 100 mL of soap. Adjust the cannon’s air and solution controls to get the coverage you want; the product directions allow adding more soap for thicker foam. Apply it to a pre-rinsed vehicle, let it dwell for 3 to 10 minutes, and rinse thoroughly with high-pressure water. Work on cool surfaces out of direct sunlight, and shorten the dwell time whenever conditions might cause the foam to dry.
How many washes will the 1 L or 4 L soap option provide?
At the stated starting amount of 100 mL per foam cannon fill, 1 L contains enough soap for ten measured fills and 4 L for forty. That is a measure of soap portions, not a guaranteed number of complete vehicle washes. A large truck, a particularly muddy vehicle, or a thicker foam setting may require more solution or multiple fills. For a small ATV or UTV, you may use less than a full bottle of mixed solution. Choose the size based on how often and what you wash rather than treating the calculated fills as a fixed yield.
Will the foam cannon remove all the mud without hand washing?
It can loosen and rinse away a substantial amount of dirt, but a touchless pass may not remove every trace of mud or road film. Dried buildup around badges, trim edges, wheel arches, and lower panels can require another rinse or a careful contact wash. The foam stage is valuable because it removes as much contamination as practical before a mitt touches the vehicle. Check the surface after rinsing and avoid wiping through remaining grit. For very heavy deposits, repeat the pre-rinse and foam process where needed.
Does Offroader Power Wash leave any protection behind?
Yes. UNLOCKD describes Offroader Power Wash Soap as leaving a protective sealant layer intended to help make later mud and debris easier to clean. The product page does not state a specific durability period, so the effect should be treated as a wash-applied benefit rather than a replacement for a dedicated long-term coating. Its persistence will depend on subsequent driving, weather, and washing. If you want additional hydrophobic protection after cleaning, UNLOCKD suggests following the wash with a separate spray protection product.
Can I use this kit on a ceramic-coated or waxed off-road vehicle?
The kit page does not give a specific compatibility guarantee for ceramic coatings, waxes, or paint protection film. If your vehicle has one of these finishes, check its care instructions and test the soap on a small, inconspicuous area before washing the entire vehicle. Offroader Power Wash leaves its own protective layer, which may affect how an existing finish looks or sheds water immediately after washing. Rinse thoroughly, keep the soap from drying, and follow any cleaning restrictions supplied by the coating or film manufacturer.
Will the foam cannon clean underneath my truck or Jeep?
The Hypersuds Foam Cannon is designed to apply soap across accessible exterior surfaces; it is not an undercarriage cleaning attachment. You can foam reachable lower panels, bumpers, and wheel-arch areas, but thick mud lodged underneath the vehicle needs a thorough water rinse and may require a dedicated undercarriage tool. Pay particular attention to places where mud collects after a trail ride. Removing those deposits separately also lets the Offroader Power Wash foam work on the visible bodywork instead of relying on it to dislodge packed mud from hidden areas.
